MOBILE AERIAL WHIPS

Key to picture:

Top: Hinge lug end

Second from top: Dual band

Next: PL259 end

Bottom: plain end

 

We can supply mobile aerial whips compatible with our magnetic bases, and certain other manufacturers' aerial bases.

We use only the highest grade 17/7PH stainless steel.

QUARTER WAVE WHIPS

These are available for frequencies from 70 MHz upwards.

For convenience of stocking, we break down into three ranges:

70 to 100MHz

100 to 200MHz

200MHz upwards.

Whips can be supplied cut for the bottom frequency in each range or cut to order for a frequency within the range.

All whips are normally supplied with a protective plastic tip, and may be either plain ended or fitted with a range of end connections.

PRICES

FREQUENCY

PLAIN ENDED

3/8" UNF ADAPTOR

HINGE ADAPTOR

PL259 **

70 to 120MHz

2.45 *

Pt No: 551

3.45 *

Pt No: 552

3.45 *

Pt No: 553

4.45 *

Pt No: 554

120 to 200MHz

1.50

Pt No: 555

2.50

Pt No: 556

2.50

Pt No: 557

3.75

Pt No: 558

200MHz up

1.50

Pt No: 559

2.50

Pt No: 560

2.50

Pt No: 561

3.75

Pt No: 562

** Other co-axial fittings can be supplied to order, please enquire.

DUAL BAND WHIPS (2m/70cm)

Coverage 144-146MHz and 430-440MHz

This British made product is extremely compact, yet highly efficient Dual Band aerial which gives superb results due to expert design.

The excellent performance offered by this aerial has been achieved by careful matching, and good horizontal radiation patterns on both bands.

It has unity gain at 2metres and 3dBd at 70cm.

Don't be put off by the truthful, but apparently meagre claims for gain. Often, aerials claiming higher gain fail to hit the target due to ineffective radiation patterns. Also, bear in mind that many imported American and Oriental aerials quote gain in "dBi" which refers to an "abstract point source in space". When comparing figures given in "dBi" with those in "dBd", remember to subtract 2.7 from the "dBi" figure.

Measuring only 46cm long, this aerial is neat and slim. Made from high quality materials, it is extrememly robust. The whip is top grade stainless steel, and the coil is fully sealed so there is no need to worry about corrosion.

It is normally supplied with a hinge lug to fit our type 503 magnetic mounts.

Part Number 563: Price: GBP 18.50

Fitted with Straight 3/8" UNF adaptor: Part Number 564: GBP 18.50

Fitted with PL259: Part Number 565: GBP 19.50

(NOTE: please are prepared to supply this last item due to popular demand, however, due to the doubtful characteristics of the PL259 at UHF, we are unable to guarantee the performance.)

 

CARRIAGE

ORDERS of total value (ALL PRODUCTS) UNDER GBP 10.00, PLEASE ADD GBP 2.00

Over GBP 10.00 POST FREE.

EXCEPT *: we're very sorry, we try hard not to rip-off where carriage is concerned, BUT whips over 30 inches long have to go by PARCEL POST and NEED SPECIAL PACKING (long boxes and stiffeners). This all means a lot of extra cost; for all whips marked *, please ADD GBP 5.00 carriage for ANY QUANTITY.

THE GBP 5.00 CHARGE ALSO APPLIES TO MAGNETIC BASES REGARDLESS OF THE WHIP SUPPLIED.

 

[HOME] [BACK] [Active NOMAD] [Passive NOMAD] [FLEXIWHIPS] [ANGLER] [JIMP] [MAG MOUNTS] [LONGWIRE]